22 Pin Expansion Harness for MXL2/MXS/MXP/MXG
22 pin expansion harness for MXL2, MXS, MXP and MXG is wired for 4 analog channels, 3 digital speed channels and unterminated wire leads for RS232 ECU, 2nd CAN input...
$ 410.00
37 Pin Main Harness for MXL2/MXS/MXG
37 pin main harness for MXL2, MXS and MXG is wired for 4 analog channels,1 digital speed channel, USB communication, CAN Expansion, IR Lap Beacon and unterminated wire leads for...
$ 490.00
AiM 719 - 712 Patch Cable
These patch cables have a metal connector on the logger side and a plastic connector on the sensor side for use with EVO4S, EVO4, XG Log data systems and Channel...
$ 48.00
AiM 719 - 719 Patch Cable
These patch cables have plastic connectors on both ends and are used on MXG, MXP, MXS, MXL2, as well as MXL Strada/Pista/Pro systems.
$ 32.00
AiM G/GS-Dash Mounting Bracket
Anodized .063 aluminum bracket for mounting an AiM EVO4 G-Dash on a Momo Model 27 cut top steering wheel.
$ 30.00
AIM-LCU1S
Smaller, Lighter and Faster! Kit includes a LCU1S Controller, Bosch LSU 4.9 lambda sensor and steel bung. LCU1S wideband Lambda controller allows to perfectly tunethe carburetion of your engine...
$ 419.00
AIM-Open USB Harness
7P male Binder 712 connector to USB used to program AiM Open System products like the GPS09, LCU1S and Keypads. Cable length is 11'/0.3m. AiM P/N V02551690.
$ 58.00
Brake Manifold (1/8 NPT & 3/8-24 Ports)
Machined aluminum manifold for 1/8 NPT male brake pressure sensors. Two 3/8-24 ports on the sides, and one 1/8 NPT port on the bottom for the pressure sensor. Bleed screw...
$ 70.00
ECU to SmartyCam GP HD 2.2 Cable, 2m
Cable for connecting a SmartyCam GP HD Rev 2.2 video system to a CAN ECU. Visit AiM's web site https://aim-sportline.com/en/documentation.htm to confirm that your ECU is supported.) Binder 712 7...
$ 96.00
EVO4 CAN/RS232 ECU Cable
This cable connects the EVO4 to various automotive and motorcycle ECU's. See AIM's web site for a complete list of supported ECU's and pin out information. Cable is un-terminated so...
$ 51.00
EVO4 K-Line/Coil Cable
This cable connects the AIM EVO4 to all non ECU RPM pickups - existing square wave tach signal, negative side of coil, and certain motorcycle K-line ECU's. Check AiM's web...
$ 60.00
EVO4S CAN ECU Cable
EVO4S CAN ECU cable - 7 feet long with 7-pin male Binder 712 connector on one end and flying leads for CAN+, CAN- and Ground.
$ 73.00
EVO4S RPM+Digital Output Cable
5 pin 712 male with 59"/1.5m flying leads for RPM (square wave tach signal or low voltage negative side of the coil pickup), digital output (control external devices such as...
EVO5 37 Pin Main Harness - Standard
37 pin main harness for MXL2, MXS, MXP and MXG is wired for 2 analog channels, 2 Thermocouple channels, 1 digital speed channel, USB communication, CAN Expansion, GPS and unterminated...
$ 470.00
GPS09 Module
Connects to any AiM logger with a CAN expansion port and the SmartyCam GP HD Rev 2.2. GPS09 is more precise: while GPS08 included GPS satellite signal and Global Navigation...
$ 399.00
IR Beacon Receiver 712, 3m
Standard IR beacon for an MXL Pista (9'-8" cable) with metal connector. Can also be used with XG Log.
IR Beacon Receiver 719-Long
AIM IR beacon with plastic 719 connector. 9'-8" cable length.
$ 59.00
IR Beacon Receiver 719-Short
IR beacon with plastic connector for use with MyChron 3 Gold, Plus and MXL Pro. 32 inch cable length.
LCU-One CAN Lambda Controller
AIM's LCU-One includes a wideband lambda controller module, Bosch LSU 4.9 sensor and weld-in bung. This model connects to the logger through via the CAN expansion port or Data Hub....
Magnet for Magnetic Wheel Speed Sensor, M4 (0.70mm) Stud
Replacement magnet in 4mm brass sleeve with M4 threaded post for use with AiM magnetic wheel speed sensors.
$ 9.00